FAQ Frequently Asked Questions

Contact us

We are happy to answer your questions. Here you will find a compilation of frequently asked questions about our various measurement services. If you have further questions or the answers are not enough, please call us!

We use optical and tactile measuring systems. In optical systems, a point on a surface is measured without contact or by marking the surface at discrete points; in tactile measuring systems, the object surface is probed with a spherical probe (sample). The individual points can then be used to calculate corresponding replacement elements (distances, circle, plane, line, ellipsoid, etc.) with the measuring software.

We can carry out extensive measurements of objects. See the <link internal-link>3D Scanning section.

Installation and various preparations of the measuring systems take approx. 30 minutes. Then the actual measurement begins.

For standard measuring tasks under good measuring conditions, we achieve a measuring accuracy of 1:100 000, i.e. the ratio between measuring accuracy and object size is 1:100 000. depending on measuring volume and measuring strategy, measuring accuracies in the range of a few micrometers (0.001 mm) are possible.

The size of the object to be measured is limited to a specific object size solely by the economic efficiency of the technologies we use. Typically we measure objects in the order of a few meters up to approx. 60 m. Our systems can also be used economically for measuring objects with an extension of several 100 m.

Depending on the measurement accuracy achieved and the applied ratio of tolerance to measurement accuracy, the smallest tolerances that can be tested by us are in the range of a few 1/100 mm.

We also carry out measurements abroad. We have worldwide contacts to other measurement service providers. This allows us to react flexibly to our customers' requirements. In recent years we have been active in Europe, Japan, China, Brazil, Mexico, USA, Egypt, Azerbaijan, Pakistan, Taiwan and South Korea.

Due to the size of our company and the capacities available, we are usually able to react very quickly to requirements. It is always helpful if an approximate date is given as early as possible (e.g. calendar week). Then we can plan our capacities accordingly in advance. The exact deployment date can then be arranged, for example, one week in advance.

The expansion of the measuring object due to temperature can (and must) be compensated with the measuring software used. The object temperature can be measured with material temperature sensors. The accuracy of the temperature measurement then influences the accuracy of the measurement itself.

We use methods to mathematically compensate for possible temperature changes and thus geometric changes of the measured object during the measurement. A change in the temperature of the measurement object during measurement always has a negative effect on the measurement accuracy and thus on the measurement statement.

By using special technologies or by combining different measuring methods, even points that are difficult to access can be measured. Each point is measurable if the corresponding measurement effort is economically justifiable.

We are specialized in mobile 3D measurement technology. This means that we perform the measurement at your site with our measuring equipment. Our systems are designed so that measurements are possible even under difficult conditions. The measurement results are basically comparable to a conventional 3D coordinate measurement on a CMM (stationary coordinate measuring machine).

Depending on the measurement technology used, the object must be in a stable position or can move in a certain frequency range, then this movement must be detected simultaneously. Any influence such as vibration or temperature can be compensated. However, any compensation leads to a reduction in measurement accuracy. Therefore, the question of the ambient conditions is always connected with the question of the tolerance to be tested or the required measuring accuracy.

The measurement can be performed with a laser tracker. For this purpose, the device is positioned on a heavy-duty stand at a height of 5 m. The measurement of the bearing aisles is carried out from two device positions, each in the axis of the aisles. Each gas diameter is measured with several measuring points and thus circles and cylinders are calculated. The device positions are linked to each other via reference points. The evaluation and documentation of the measurement takes place directly on site, so that immediately after the measurement a decision can be made about a possible pending reworking of the lanes. The measurement accuracy for this measurement is 0.020 mm for the bearing race diameter, 0.025 mm for the straightness of a single race and 0.035 mm for the parallelism and the height difference.

No. As long as the object is not deformed by its storage, it is completely irrelevant how the object is positioned during the measurement. The relation between measuring system and object is determined by measurement (by the so-called mathematical alignment).

We use technologies and methods that compensate for a movement of the target (be it a slow drift or a continuous movement) or that can take measurements on moving objects. In this specific case it has to be check whether a measurement is possible.

Get in touch with us!

Phone: +49 2542 91898-0

Send e-mail